How to use System Texsolv |
| |
 System Texsolvis is developed to facilitate rapid and easy set up of the weave. The system gives the weaver a quiet and smooth weaving experience, with low friction and minimal problems. The weave will turn out smooth and even. There is a reason why people all over the world prefer System Texsolv! |
Heddles set up
|
|
|
|
|
| Start with one bundle at the time, 100 heddles in each bundle. NOTE do not remove bundle clips until the bundle is mounted on the loom shaft |
|
| | |
|
|
| Before mounting the bundle on the shaft, identify the end loops and make sure the heddles not get tangled up |
|
|
|
|
| Mount the bundle on to the loom shaft, through the end loops. Move the bundle to the desired position |
|
| | |
|
|
| Remove the first two clips in one end, do it carefully |
|
|
| Then remove the other two on the opposite side |
|
|
|
|
| Locate the first heddle in the bundle and pull it out |
|
| | |
|
|
| Heddle number two and three and so on will now follow. This accommodates for a rapid and simple set up on the shaft. |
|
|
|
|
Threading
|
|
|
|
|
| Threading of the warp is done fast and easy thanks to the open construction of the heddles. Use Texsolv's thread hook for rapid and easy threading |
To Measure a heddle |
|
|
|
|
If the length of a heddle is unknown, it can easily be measured. To do so, stretch the heddle by the use of two sticks (as the pictures shows) and hold it against a measuring tape to determine the lenght. Moderate tightening |
Remove or replace a heddle. |
|
|
|
|
| Separate the heddle that u wish to remove from the chain, by cutting it on the top side |
|
| | |
|
|
| Then do the same on the other end. Then cut the heddle in the center to completely release it from the shaft |
|
|
|
|
To replace a misplaced or broken heddle, a so called replace heddle is used. This heddle can be ordered in any size available. The replace heddle is normal in one end and open in the other. Mount the loop side over the top shaft |
|
| | |
|
|
| Pull the heddle through/under the outer heddles to the desired position |
|
|
|
|
| Make sure that the bottom threads of the replace heddle ends up on each side of the lower shaft |
|
| | |
|
|
| Then tie the replace heddle around the lower shaft. Cut of the left over threds |
|
|
|
|
|
|
| The eye of the replace heddle will end up on the same level as the other heddles. Fast and easy! |
|
|
Basic coupler locks |
|
|
 The Texsolv anchor peg is excellent to use on drilled holes, common on treadles and lamms, where adjustment is necessary. Ideal hole diameter is 5,5 mm. The pegs are used to lock the polyester loop cord in place. To do so the cord is attached to the "hook" on the side of the peg, then the peg is secured in the hole by the use of the two "legs". The length of the cord is then easily adjusted by moving the peg up or down on the cord. |
 Texsolv straight peg is used where loops are used that easily have to be adjusted in height, or where anchor pegs can't be used. The straight peg system is similar to the running loop below, with one significant advantage, it can adjusted, fast and easy. |
 The simple running loop is used as fixed attachment, where adjustment isn't necessary, e.g. warp and cloth beam
|
|
|
| Rocker arm mounted with straight peg, and running loop as fixed attachment to heddle harness |
|
|
| tree different ways of mounting the cord to drilled holes on e.g. lamms or treadles |
Fixed attachment to warp or cloth beam
|
|
|
|
|
| Count the holes in the beams. Cut the right amount of cord in the EXACT same length |
|
|
Run the beam cord through the hole in the beam
|
|
| | |
|
|
| Create a running loop around the beam, use beam cord 1/20 |
|
|
| Tighten it |
|
|
|
|
Then the tying rod is attached by another running loop
|
|
|
Connecting Treadle and lamm with straight peg lock |
|
|
|
|
| Treadle and lamm with drilled holes |
|
|
| Adjust the height and lock it by using an anchor peg |
|
| | |
|
|
| Run tie up cord 1/12 through the hole |
|
|
| Secure the cord loop carefully around the hook on the peg |
|
|
|
|
| Then pull the cord back to lock the peg in the hole by the use of the legs on the peg, make sure it is safely secured and that the legs goes into the hole |
|
|
| The running loop is excellent to use as a fixed attachment on the lamm, it's the same system that is used in the instructions above |
|
| | |
|
|
Rocker arm tie up with anchor peg |
|
|
|
|
| A rocker arm is easily attached by creating a loop |
|
|
when the correct height is adjusted the cord is locked with a straight peg
|
|
| | |
|
|
| at the point where the tie up cord runs through itself |
|
|
Make sure that the peg is safely inserted into the loop and locked
|
|
|
|
|
| The height can easily be adjusted by moving the peg up or down in the cord loops |
